We serviced a
SAMSUNG DRYER
Model DV48H7400GW/A2
Near Marina del Rey, California 90292
Joel M.
Job Details:
12/08/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required thermal fuse was installed successfully.After installation, I performed maintenance, cleaning and functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of dryer not starting.; pckd up 1 DC47-00016A (THERMOSTAT HI LIMIT)"
We serviced a
WHIRLPOOL DRYER
Model WGD72HEDW1
Near Los Angeles, California 90066
Joel M.
Job Details:
12/08/2025
"The client requested annual maintenance on the dryerNo prior complaints about the unit's performance were reported by the customer.Performed the following tasks:-Vacuumed dryer interior (lint chute, blower housing, motor bay)-Inspected belt, idler pulley, rollers, and seals-Functional test of heating cycle and temperature rise-Performed airflow test at unit-to-wall vent connectionResult:Issues found, recommend further repair: vent in wall clogged, need vent cleaning company to clear."
We serviced a
WHIRLPOOL OVEN
Model WFE515S0EW1
Near Culver City, California 90230
Joel M.
Job Details:
12/08/2025
"Returned to complete the repair on the unit after the initialdiagnosis. The required infinite switch was installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of burner heat shoots up."
We serviced a
LG WASHER
Model WM4270HVA
Near Los Angeles, California 90035
Joel M.
Job Details:
12/08/2025
"Performed diagnostic on the unit. The customer reported that washer leaking. Upon inspection, I performed leak test. The results showed that door boot torn. The issue occurred due to incidental. In order to resolve the problem, the following repair is needed: replace door boot. ; ordrng 1 MDS47123631 (BELLOWS)"
We serviced a
LG WASHER
Model WM2140CW
Near Los Angeles, California 90034
Joel M.
Job Details:
12/08/2025
"Performed diagnostic on the unit. The customer reported that washer leaking. Upon inspection, I performed leak test. The results showed that door boot torn. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace door boot. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 4986ER0004F (BELLOWS) from stock"
We serviced a
BOSCH DISHWASHER
Model SHVM78Z53N/20
Near Los Angeles, California 90291
Joel M.
Job Details:
12/08/2025
"Performed diagnostic on the unit. The customer reported that dishwasher display fill salt and rinse aid. Upon inspection, I performed function test to unit. The results showed that power module not responsive. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace power module .
We serviced a
WOLF OVEN
Model SO30-2U/S-TH
Near Los Angeles, California 90291
Joel M.
Job Details:
12/05/2025
"Performed diagnostic on the unit. The customer reported that oven displays MDL error. Upon inspection, I performed door lock resistance test. The results showed that lock according to specifications. The issue occurred due to common communication fault. In order to resolve the problem, the following repair is needed: factory reset unit.
We serviced a
MAYTAG DRYER
Model MGDB755DW0
Near Los Angeles, California 90049
Joel M.
Job Details:
12/05/2025
"The client requested annual maintenance on the dryer. Prior complaint about the bracelet stuck in blower was addressed by removing bracelet from blower.Performed the following tasks:-Vacuumed dryer interior (lint chute, blower housing, motor bay)-Inspected belt, idler pulley, rollers, and seals-Functional test of heating cycle and temperature rise-Performed airflow test at unit-to-wall vent connectionResult:Upon inspection, no issues observed dryer in good condition."
We serviced a
SAMSUNG REFRIGERATOR
Model RSG257AARS/XAA
Near Los Angeles, California 90049
Joel M.
Job Details:
12/05/2025
"Performed diagnostic on the unit. The customer reported that refrigerator not cooling. Upon inspection, I performed voltage testing to inverter. The results showed that inverter getting voltage but not responding. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace inverter
We serviced a
LG WASHER
Model WM8900HBA
Near Beverly Hills, California 90210
Joel M.
Job Details:
12/05/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required inner door and door latch were installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of door not closing."
We serviced a
LG WASHER
Model WM3900HWA
Near Culver City, California 90230
Joel M.
Job Details:
12/05/2025
"Performed diagnostic on the unit. The customer reported that washer leaking. Upon inspection, I performed water valve test and ran test cycle. All components tested within manufacturer specifications, and no mechanical, electrical, or operational issues were detected during the visit. At this time, the unit is operating as designed and does not require any repairs. The customer was advised to continue monitoring the appliance and to contact us if the issue reoccurs or worsens. This service call is warranted for 14 days from the date of the visit, in case the same issue reappears."
We serviced a
GENERAL ELECTRIC OVEN
Model JGBP28DED1WH
Near Santa Monica, California 90405
Joel M.
Job Details:
12/04/2025
"Performed diagnostic on the unit. The customer reported that oven not heating. Upon inspection, I performed resistance testing on bake igniter. The results showed that line open. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace bake igniter. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 GR403 (IGNITER - OVEN GLOW FRONT INSTALLED) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED5GTGXNQ10
Near Los Angeles, California 90016
Joel M.
Job Details:
12/04/2025
"Performed diagnostic on the unit. The customer reported that refrigerator leaking. Upon inspection, I performed physical assessment of water reservoir. The results showed that reservoir leaking and cover has black mold. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace reservoir and back panel
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814TWB
Near Los Angeles, California 90035
Joel M.
Job Details:
12/04/2025
"Performed diagnostic on the unit. The customer reported that refrigerator not cooling. Upon inspection, I performed resistance testing on compressor windings. The results showed that windings out of spec. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed:replace compressor. The total cost for the repair is not cost effective. Recommend replacing refrigerator.
We serviced a
SPEED QUEEN WASHER
Model SWNBC2PP112TW01
Near Los Angeles, California 90049
Joel M.
Job Details:
12/04/2025
"Returned to complete the repair on the unit after the initialdiagnosis. The required belt and pulley assembly were installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of strange noise and smells of burning plastic."
We serviced a
BOSCH DRYER
Model WTE86300US/08
Near Los Angeles, California 90293
Joel M.
Job Details:
12/04/2025
"Performed diagnostic on the unit. The customer reported that dryer leaking. Upon inspection, I performed visual assessment of cooling box and door. The results showed that door broken and not always engaging and cooling box damaged. The issue occurred due to abuse. In order to resolve the problem, the following repair is needed: replace cooling box and door panel.
We serviced a
SAMSUNG DRYER
Model DV48H7400GW/A2
Near Marina del Rey, California 90292
Joel M.
Job Details:
12/03/2025
"Performed diagnostic on the unit. The customer reported that dryer not starting. Upon inspection, I performed continuity test on thermal fuse. The results showed that circuit is open. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace thermal fuse..; ordrng 1 DC47-00016A (THERMOSTAT HI LIMIT)"
We serviced a
MIELE DRYER
Model TWF160WP
Near Los Angeles, California 90066
Joel M.
Job Details:
12/03/2025
"The client requested annual maintenance on the dryer.Beeping complaint about the unit's were due to need of maintenance.Performed the following tasks:-Vacuumed dryer interior (lint chute, blower housing, motor bay)-Inspected belt, idler pulley, rollers, and seals-Functional test of heating cycle and temperature rise-Performed airflow test at unit-to-wall vent connectionResult:Upon inspection, no issues observed dryer in good condition."
We serviced a
LG WASHER
Model WM8900HBA
Near Beverly Hills, California 90210
Joel M.
Job Details:
12/03/2025
"Performed diagnostic on the unit. The customer reported that washer door not close. Upon inspection, I performed physical assessment of door latch. The results showed that strike caught in latch because inner door holder broke. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace inner door and door latch.
We serviced a
SAMSUNG REFRIGERATOR
Model RSG257AARS
Near Los Angeles, California 90035
Joel M.
Job Details:
12/03/2025
"Performed diagnostic on the unit. The customer reported that LEDs faulty and not cooling. Upon inspection, I performed voltage test on display and inspection of sealed system. The results showed that display getting voltage but faulty and sealed system leaking refrigerant overheating compressor. The issue occurred due to wear and tear. The total cost for the repair is not cost effective. Recommend replacing unit at this time.
We serviced a
KENMORE DRYER
Model 110.71202010
Near Los Angeles, California 90064
Joel M.
Job Details:
12/03/2025
"Performed diagnostic on the unit. The customer reported that dryer not turning on. Upon inspection, I performed physical assessment of door switch. The results showed that door switch broken. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace door switch. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 WP3406107 (DOOR SWITCH) from stock"
We serviced a
MAYTAG DRYER
Model MLE2000AYW
Near Los Angeles, California 90024
Joel M.
Job Details:
12/03/2025
"Performed diagnostic on the unit. The customer reported that dryer making noise and not start. Upon inspection, I performed physical assessment of motor assembly. The results showed that clip broken damaging motor ,blower and housing. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace motor , blower, housing and clip.
We serviced a
KENMORE REFRIGERATOR
Model 596.72282202
Near Santa Monica, California 90403
Joel M.
Job Details:
12/02/2025
"Performed diagnostic on the unit. The customer reported that refrigerator freezing food. Upon inspection, I performed physical assessment of cold control. The results showed that cold control track out of place. The issue occurred due to incidental. In order to resolve the problem, the following repair is needed: reinstall cold control track. The customer approved the repair during this visit, and the required parts were reinstalled successfully. After reinstallation, I performed functional testing to confirm the repair. The unit is now operating as designed. Complementary maintenance and cleaning was performed at this time. This repair resolves the previously identified issue."
We serviced a
WHIRLPOOL OVEN
Model WFE515S0EW1
Near Culver City, California 90230
Joel M.
Job Details:
12/02/2025
"Performed diagnostic on the unit. The customer reported that oven not heating. Upon inspection, I performed manufacture specification test on heating components. The results showed that components are within specifications, no mechanical failure. During my diagnosis I discovered right front burner switch was blown. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace burner switch..; ordrng 1 WP3149400 (SWITCH - BURNER (STANDARD 5500 TYPE))"
We serviced a
SAMSUNG WASHER
Model WA50R5200AW/US
Near Los Angeles, California 90045
Joel M.
Job Details:
12/02/2025
"Performed diagnostic on the unit. The customer reported that washer banging around displaying ub error. Upon inspection, I performed physical assessment of suspension. The results showed thatsuspension rods worn. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace suspension rods.
We serviced a
MAYTAG WASHER
Model MVW6230RHW0
Near Beverly Hills, California 90211
Joel M.
Job Details:
12/01/2025
"Performed diagnostic on the unit. The customer reported that washer not wringing out clothes. Upon inspection, I performed function test cycle. The results showed that some buildup in drain pipes. The issue occurred due to lack of maintenance. In order to resolve the problem, the following repair is needed: conduct full maintenance and cleaning of unit. The customer approved the repair during this visit, and the required service was performed successfully. After completion, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue."
We serviced a
SPEED QUEEN DRYER
Model SDGT09WF
Near Los Angeles, California 90049
Joel M.
Job Details:
12/01/2025
"Performed diagnostic on the unit. The customer reported that dryer not starting after reprogram attempt. Upon inspection, I performed function test on unit. The results showed that reprogram done incorrectly. The issue occurred due to admin error. In order to resolve the problem, the following repair is needed: reprogram unit. The customer approved the repair during this visit, and the required reprogramming was performed successfully. After reprogramming, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue."
We serviced a
SPEED QUEEN DRYER
Model SDG109WF
Near Los Angeles, California 90066
Joel M.
Job Details:
12/01/2025
"Returned to complete the repair on the unit after the initialdiagnosis. The required motor was installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of making loud noise."
We serviced a
SUBZERO WINE COOLER
Model UW-24/S/TH
Near Marina del Rey, California 90292
Joel M.
Job Details:
11/28/2025
"The client requested annual maintenance on the refrigerator. $299No prior complaints about the unit's performance were reported by the customer. Performed the following tasks:-Visual inspection of door seals/gaskets for wear or gaps-Cleaned condenser coils (accessible areas only)-Checked and cleaned drain pan (if accessible)-Verified interior and door lights function-Temperature check (fridge + freezer) with digital thermometer-Functional test of cooling cycle and compressor operationResult:Upon inspection, no issues observed refrigerator in good condition."
We serviced a
WHIRLPOOL DRYER
Model WGD87HEDW0
Near Los Angeles, California 90056
Joel M.
Job Details:
11/28/2025
"Performed diagnostic on the unit. The customer reported that dryer making noise. Upon inspection, I performed run test on all moving components. The results showed that idler pulley worn. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace pulley and conduct annual maintenance. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 279640 (IDLER PULLEY) from stock"
We serviced a
KENMORE WASHER
Model 796.40512900
Near View Park-Windsor Hills, California 90043
Joel M.
Job Details:
11/28/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that washer not starting. Upon inspection, I performed resistance testing and confirmed that the issue is the same as the one previously repaired on 11/6. Since the same problem reoccurred within 90 days of the original repair but outside of 14 days of service, this visit is covered under our parts and labor warranty both parts and labor are covered at no cost to the customer but a service call is due. The required door lock was replaced as needed. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue, and the visit was completed under full warranty coverage. This repair remains covered under the original 90-day labor and 1-year parts warranty from the first installation date(subject to manufacturer availability).; used 1 EBF49827801 (DOOR LOCK) from stock"
We serviced a
ELECTROLUX DRYER
Model NOTAVAILABLE
Near Los Angeles, California 90047
Joel M.
Job Details:
11/28/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that dryer not starting E66. Upon inspection, I performed continuity test and confirmed that the issue is the same as the one previously repaired on 11/13. Since the same problem reoccurred within 90 days of the original repair and within 14 days of service, this visit is covered under our full warranty both parts and labor are covered at no cost to the customer. The required high limit thermostat was replaced as needed. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue, and the visit was completed under full warranty coverage. This repair remains covered under the original 90-day labor and 1-year parts warranty from the first installation date(subject to manufacturer availability).; used 1 137032600 (HIGHT LIMIT THERMOSTAT) from stock"
We serviced a
KENMORE DRYER
Model 41799872990
Near Los Angeles, California 90291
Joel M.
Job Details:
11/28/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required felt ,glides, sensor and belt were installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of no heat and damaging clothing.; used 1 137292700 (BELT), and 1 5303281135 (GLOW IGNITER SENSOR) from stock"
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDT545PSJ2SS
Near Los Angeles, California 90291
Joel M.
Job Details:
11/28/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required user interface and harness were installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of no power."
We serviced a
KITCHEN AID WASHER
Model KAWS750JQ0
Near Marina del Rey, California 90292
Joel M.
Job Details:
11/26/2025
"Performed diagnostic on the unit. The customer reported that washer not spinning. Upon inspection, I performed function testing on timer. The results showed that lid lock not engaging. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace lid lock. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; dspstn on spec-tagged invntry: 1 3949247 SWITCH"
We serviced a
KITCHEN AID DISHWASHER
Model KDTM604KPS1
Near Los Angeles, California 90066
Joel M.
Job Details:
11/26/2025
"Performed diagnostic on the unit. The customer reported that dishwasher slanted. Upon inspection, I performed visual assessment of legs. The results showed that one leg screwed itself in. The issue occurred due to normal wear. In order to resolve the problem, the following repair is needed: raise leg to match desired height of unit.
We serviced a
KITCHEN AID RANGE
Model KSGG700ESS2
Near Los Angeles, California 90049
Joel M.
Job Details:
11/26/2025
"Performed diagnostic on the unit. The customer reported that center burner not lite. Upon inspection, I performed physical assessment of burner. The results showed that burner out of place. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: adjust center burner. The customer approved the repair during this visit, and the required adjustment was made successfully. After adjusting, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue."
We serviced a
VIKING RANGE
Model VGIC3656BSS
Near Los Angeles, California 90025
Joel M.
Job Details:
11/25/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required spark module and front right electrode were installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of burners keep clicking while in use."
We serviced a
FRIGIDAIRE OVEN
Model PLGS389ECF
Near Los Angeles, California 90025
Joel M.
Job Details:
11/25/2025
"Performed diagnostic on the unit. The customer reported that broil element not come on. Upon inspection, I performed resistance testing on igniter. The results showed that igniter open. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace broil igniter. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 IG9998 (IGNITER - OVEN GLOW BAKE) from stock"
We serviced a
THERMADOR REFRIGERATOR
Model KBURT3651A02
Near Los Angeles, California 90046
Joel M.
Job Details:
11/25/2025
"Performed diagnostic on the unit. The customer reported that refrigerator temp fluctuates. Upon inspection, I performed sealed system testing. The results showed that unit leaking refrigerant. The issue occurred due to wear and tear. In order to temporarily resolve the problem, the following repair is needed: add refrigerant. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.This repair is NOT covered under our warranty policy."
We serviced a
KENMORE DISHWASHER
Model 665.13003N511
Near Culver City, California 90230
Yotam M.
Job Details:
11/25/2025
"Performed diagnostic on the unit.The customer reported that m the dishwasher is making a loud squilling noise. Upon inspection, I performed a visual test on the machine and auditorial test. The results showed that the inlet valve is making a noise while open. The issue occurred due to normal wear and tear.In order to resolve the problem, the following repair is needed: uninstall dishwasher from cabinet and replacing valve and installing back the dishwasher.
We serviced a
AMANA DISHWASHER
Model ADB1000AWS1
Near Beverly Hills, California 90212
Joel M.
Job Details:
11/25/2025
"Performed diagnostic on the unit. The customer reported that the dishwasher not clean dishes or fully drain. Upon inspection, I performed resistance testing on motor. The results showed that over unit specifications. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace motor and pump assembly . The total cost for the repair will be determined by office after conclusion of parts and availability request.; rqstng P&A on 1 WPW10247394 (MOTOR/PUMP ASSM)"
We serviced a
KENMORE WASHER
Model 110.20232711
Near Los Angeles, California 90066
Joel M.
Job Details:
11/24/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that washer not starting. Upon inspection, I performed visual assessment and confirmed that the issue is the same as the one previously repaired on 11/20. Since the same problem reoccurred within 90 days of the original repair and within 14 days of service, this visit is covered under our full warranty both parts and labor are covered at no cost to the customer. The required agitator was reinstalled as needed. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue, and the visit was completed under full warranty coverage. This repair remains covered under the original 90-day labor and 1-year parts warranty from the first installation date(subject to manufacturer availability)."
We serviced a
SPEED QUEEN DRYER
Model SDG109WF
Near Los Angeles, California 90066
Joel M.
Job Details:
11/24/2025
"Performed diagnostic on the unit. The customer reported that dryer not starting. Upon inspection, I performed physical assessment of motor assembly. The results showed that motor shaft worn causing major damage. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace motor assembly
We serviced a
MAYTAG DRYER
Model MGDE500VW1
Near Los Angeles, California 90045
Joel M.
Job Details:
11/24/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that dryer making noise. Upon inspection, I performed physical testing on rollers and confirmed that the issue is the same as the one previously repaired on 10/20. Since the same problem reoccurred within 90 days of the original repair and within 14 days of service, this visit is covered under our full warranty both parts and labor are covered at no cost to the customer. The required 4 drum rollers were replacedas needed. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue, and the visit was completed under full warranty coverage. This repair was confirmed by the customer after acknowledgment of new roller vendor not under warranty.
We serviced a
SPEED QUEEN DRYER
Model ADG30RGS111TW01
Near Los Angeles, California 90293
Joel M.
Job Details:
11/24/2025
"Performed diagnostic on the unit. The customer reported that dryer not heating. Upon inspection, I performed function testing on gas coils. The results showed that coils faulty. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace gas coils. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 279834 (GLOW IGNITER ASSM) from stock"
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model CDE06RP2NDS1
Near Los Angeles, California 90291
Joel M.
Job Details:
11/24/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that refrigerator not cooling. Upon inspection, I performed amperage test and confirmed that the issue is not the same as the one previously repaired on 11/21. Since the same problem reoccurred within 90 days of the original repair and within 14 days of service, this visit is covered under our parts and labor warranty at no cost to the customer. The required repair is not cost effective.
We serviced a
SUBZERO REFRIGERATOR
Model 650/S
Near Marina del Rey, California 90292
Joel M.
Job Details:
11/21/2025
"Performed diagnostic on the unit. The customer reported that freezer has strange black residue on bottom. Upon inspection, I performed physical assessment of substance. The results showed that mold residue from freezer door not closing properly. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace left freezer rail and gasket. The total cost for the repair is $1042.13.; ordrng 1 7042262 (DOOR GASKET, FREEZER) and 1 7019625 (DRAWER RAIL)"
We serviced a
FRIGIDAIRE DISHWASHER
Model FDSH4501AS3A
Near Marina del Rey, California 90292
Joel M.
Job Details:
11/21/2025
"Performed diagnostic on the unit. The customer reported that dishwasher keeps draining. Upon inspection, I performed visual assessment of wash motor. The results showed that circulation motor leaking. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace circulation pump. The total cost for the repair is $647.79, with $109 already owed for the service call. If you choose to proceed, the remaining balance will be $538.79."
We serviced a
KITCHEN AID REFRIGERATOR
Model KBRC36FTS00
Near Culver City, California 90230
Joel M.
Job Details:
11/21/2025
"Performed diagnostic on the unit. The customer reported that freezer leaking. Upon inspection, I performed physical assessment of condensate drain, door rail and seal. The results showed that drain clogged, rail worn and seal warped. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace freezer door seal, right rail and clear condensate drain. The total cost for the repair is $1123.60, with $159 already owed for the service call. If you choose to proceed, the remaining balance will be $964.60.; ordrng 1 WP2320616 (RAIL) and 1 2302710 (DOOR GASKET, FREEZER)"
We serviced a
LG WASHER
Model WM3170CW
Near Culver City, California 90230
Joel M.
Job Details:
11/21/2025
"Performed diagnostic on the unit. The customer reported that washer shaking violently. Upon inspection, I performed physical assessment of washer tub. The results showed that counterweight screws severed and stripped tub. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace tub and bolts. The total cost for the repair exceeds cost of new unit. Recommend replacing unit. Service call $109."
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model CDE06RP2NDS1
Near Los Angeles, California 90291
Joel M.
Job Details:
11/21/2025
"Performed diagnostic on the unit. The customer reported that refrigerator not cooling under 50?. Upon inspection, I performed sealed system function test. The results showed that start device faulty. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace start device. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 8201786 (COMPRESSOR RELAY & OVERLOAD) from stock"
We serviced a
LG WASHER
Model WM3900HWA
Near Santa Monica, California 90405
Joel M.
Job Details:
11/21/2025
"The client requested annual maintenance on the washer. No prior complaints about the unit's performance were reported by the customer.Performed the following tasks:-Visual inspection of hoses, pump, seals, and shocks-Visual inspection of door rubber gasket for mold or wear-Cleaned detergent drawer & drain pump filter-Ran cleaning cycle with approved agent-Functional check of spin cycle, balance, and door latchResult:Upon inspection, no issues observed washer in good condition."
We serviced a
KITCHEN AID OVEN
Model KEBS277SSS04
Near Santa Monica, California 90405
Joel M.
Job Details:
11/21/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required bake element was installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of not heat over 350?."
We serviced a
LG DRYER
Model DLGX7901WE
Near Redondo Beach, California 90278
Joel M.
Job Details:
11/20/2025
"The client requested annual maintenance on the dryer. $299No prior complaints about the unit's performance were reported by the customer.Performed the following tasks:-Vacuumed dryer interior (lint chute, blower housing, motor bay)-Inspected belt, idler pulley, rollers, and seals-Functional test of heating cycle and temperature rise-Performed airflow test at unit-to-wall vent connectionResult:Upon inspection, no issues observed dryer in good condition."
We serviced a
ADMIRAL DRYER
Model AGD4475TQ1
Near Los Angeles, California 90293
Joel M.
Job Details:
11/20/2025
"Returned to complete the repair on the unit after the initialdiagnosis. The required door switch was installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of dryer not starting."
We serviced a
KENMORE DRYER
Model 11070602990
Near Los Angeles, California 90066
Joel M.
Job Details:
11/20/2025
"Performed diagnostic on the unit. The customer reported that the dryer not heat. Upon inspection, I performed continuity test on thermal fuse. The results showed that no continuity. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace thermal fuse. The customer approved the repair during this visit, and the required fuse was installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 WP3392519 (FUSE - NON-RESETABLE (CHECK THERMOSTATS)) from stock"
We serviced a
KENMORE WASHER
Model 110.20232711
Near Los Angeles, California 90066
Joel M.
Job Details:
11/20/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required agitator dogs assembly and suspension rods were installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of loud noise and rocking back and forth."
We serviced a
FRIGIDAIRE WASHER
Model FAFW3574KW0
Near Los Angeles, California 90291
Joel M.
Job Details:
11/20/2025
"Performed diagnostic on the unit. The customer reported that washer staying paused. Upon inspection, I performed physical testing on door hinge. The results showed that hinge damaged. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace door hinge. The total cost for the repair is $384.88.; ordrng 1 134550800CM (DOOR HINGE)"
We serviced a
KENMORE DRYER
Model 41799872990
Near Los Angeles, California 90291
Joel M.
Job Details:
11/19/2025
"Performed diagnostic on the unit. The customer reported that dryer not heating and making holes in clothing. Upon inspection, I performed continuity test on flame sensor and physical test on drum glides, felt and belt. The results showed that sensor open and drum parts worn. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace flame sensor, belt, felt, and drum glides. The total cost for the repair is $565.64.; ordrng 1 ER5303937139 (GLIDE KIT NEW) and 1 5303283286 (FELT SEAL - REAR)"
We serviced a
SAMSUNG DRYER
Model DV393GTPARA/A1
Near Los Angeles, California 90291
Joel M.
Job Details:
11/19/2025
"Performed diagnostic on the unit. The customer reported that dryer doesnt run. Upon inspection, I performed physical test on motor. The results showed that motor support snapped causing motor to go loose while running damaging air duct and blower. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace motor assembly. The total cost for the repair is $880.40, with $109 already paid for the service call. If you choose to proceed, the remaining balance will be $771.40."
We serviced a
SPEED QUEEN WASHER
Model AWNE9RSN116TW01
Near Los Angeles, California 90291
Joel M.
Job Details:
11/19/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that L1 error displayed. Upon inspection, I performed voltage test from control and confirmed that the issue is new and unrelated to the previous repair completed on 9/25/25. Since this is a new problem and not related to the prior repair, the visit is not covered under warranty. A new service call fee applies to cover diagnostic and inspection for todays visit.In order to resolve the problem, the following repair is needed: replace control board. The total cost for the repair is $982.31, with $159 already paid for the service call. If you choose to proceed, the remaining balance will be $823.31"
We serviced a
COSMO OVEN
Model COS-C51EIX
Near Culver City, California 90230
Joel M.
Job Details:
11/19/2025
"Performed diagnostic on the unit. The customer reported that oven not heat. Upon inspection, I performed physical test of element connections. The results showed that wires burnt and soldered by previous technician. The issue occurred due to lack of skilled labor. In order to resolve the problem, the following repair is needed: rewire and new terminals. The customer approved the repair during this visit, and the required service was performed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue."
We serviced a
THERMADOR REFRIGERATOR
Model T18IF800SP/58
Near Santa Monica, California 90402
Joel M.
Job Details:
11/19/2025
"Performed diagnostic on the unit. The customer reported that wants filter changed. In order to resolve the problem, the following repair is needed: replace freezer water filter. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 11034152 (WATER FILTER) from stock"
We serviced a
MIELE DISHWASHER
Model G5225SCU
Near Los Angeles, California 90049
Joel M.
Job Details:
11/19/2025
"Performed diagnostic on the unit. The customer reported that dishwasher not draining. Upon inspection, I performed function test. The results showed that customer referring to salt reservoir. The issue occurred due to lack of salt. In order to resolve the problem, the following repair is needed: conducting maintenance and cleaning. Also recommending purchasing dishwasher salt. The customer approved the repair during this visit, and the required service was performed successfully. After service, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue."
We serviced a
LG WASHER
Model WM3570HVA
Near Los Angeles, California 90049
Joel M.
Job Details:
11/19/2025
"Performed diagnostic on the unit. The customer reported that washer not spinning. Upon inspection, I performed physical testing on drive system. The results showed that stator and rotor rubbing. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace stator and rotor. The total cost for the repair is $1123.03, with $109 already owed for the service call. If you choose to proceed, the remaining balance will be $1014.03."
We serviced a
KITCHEN AID OVEN
Model KEBS277SSS04
Near Santa Monica, California 90405
Joel M.
Job Details:
11/18/2025
"Performed diagnostic on the unit. The customer reported that top oven not heat past 350?. Upon inspection, I performed resistance test on bake element. The results showed infinite resistance. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace bake element..; ordrng 1 WPW10207398 (ELEMENT - BAKE (CONCEALED))"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC300ESS07
Near Los Angeles, California 90291
Joel M.
Job Details:
11/18/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that refrigerator temp fluctuations. Upon inspection, I performed function testing and confirmed that the issue is the same as the one previously repaired on 10/30. Since the same problem reoccurred within 90 days of the original repair and within 14 days of service, this visit is covered under our full warranty both parts and labor are covered at no cost to the customer. The required damper was adjusted as needed. After installation, I performed functional testing to confirm the repair. Also noted food stored completely covering damper, advised customers against such loading practices. The unit is now operating as designed. This repair resolves the previously identified issue, and the visit was completed under full warranty coverage. This repair remains covered under the original 90-day labor and 1-year parts warranty from the first installation date(subject to manufacturer availability)."
We serviced a
SAMSUNG RANGE
Model NX58H600SS/AA
Near Los Angeles, California 90034
Joel M.
Job Details:
11/18/2025
"Performed diagnostic on the unit. The customer reported that oven not heating. Upon inspection, I performed resistance test on igniter. The results showed that igniter out of spec. The issue occurred due to wear and tear . In order to resolve the problem, the following repair is needed: replace bake igniter. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 IG9998 (IGNITOR) from stock"
We serviced a
KENMORE DRYER
Model 796.91182310
Near Beverly Hills, California 90211
Joel M.
Job Details:
11/18/2025
"Performed diagnostic on the unit. The customer reported that dryer squeaking. Upon inspection, I performed physical test on moving parts and ran a test cycle. All components tested within manufacturer specifications, and no mechanical, electrical, or operational issues were detected during the visit. At this time, the unit is operating as designed and does not require any repairs. The customer was advised to continue monitoring the appliance and to contact us if the issue reoccurs or worsens. No service call. If same issue arises unrelated to previous repairs a service call charge will be due."
We serviced a
SUBZERO REFRIGERATOR
Model 532
Near Los Angeles, California 90068
Joel M.
Job Details:
11/18/2025
"Performed diagnostic on the unit. The customer reported that freezer not cooling. Upon inspection, I performed function test on sealed system. The results showed that compressor shorted and leaking oil. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: full sealed system overhaul and conversion to r600. The total cost for the repair exceeds cost of new unit. 36 years old in bad condition, recommend replacing. Service call $199."
We serviced a
VIKING MICROWAVE
Model DM0C205SS
Near Los Angeles, California 90024
Joel M.
Job Details:
11/18/2025
"Performed diagnostic on the unit. The customer reported that microwave not heat. Upon inspection, I performed live voltage test on transformer. The results showed that excessive voltage drop through load and capacitor out of spec. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace capacitor and transformer. The total cost for the repair will be determined upon completion of parts and availability request from manufacturer. The office will contact you with results upon conclusion.; rqstng P&A on 1 PM100044 (HV CAPACITOR ASSY) and 1 028813-13 (MD TRANSFORMER)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model GB2SHDXTQ02
Near Santa Monica, California 90405
Joel M.
Job Details:
11/18/2025
"Performed diagnostic on the unit. The customer reported that refrigerator leaking and icing up. Upon inspection, I performed physical testing of seals. The results showed that door seals torn and not sealing. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace refrigerator and freezer door seals. The total cost for the repair is $853.03, with $109 already owed for the service call. If you choose to proceed, the remaining balance will be $744.03."
We serviced a
KENMORE DRYER
Model 110.70222512
Near Los Angeles, California 90066
Joel M.
Job Details:
11/17/2025
"Performed diagnostic on the unit. The customer reported that dryer timer not advancing. Upon inspection, I performed voltage test on timer. The results showed that power lost through load. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace timer.
We serviced a
KENMORE REFRIGERATOR
Model 795.71313.312
Near Los Angeles, California 90291
Joel M.
Job Details:
11/17/2025
"Performed diagnostic on the unit. The customer reported that refrigerator not cooling. Upon inspection, I performed sealed system diagnostic. The results showed that unit leaking refrigerant. The issue occurred due to lack of maintenance. In order to resolve the problem, the following repair is needed: full sealed system overhaul. The total cost for the repair exceeds cost of repair. Recommend replacing unit.
We serviced a
LG DRYER
Model DLGX4371W
Near Redondo Beach, California 90278
Joel M.
Job Details:
11/17/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that dryer squeaking. Upon inspection, I performed physical test on pulley and confirmed that the issue is the same as the one previously repaired on 7/14/25. Since the same problem reoccurred after 90 days but within 1 year of the original repair, the part is covered under warranty, but labor and service call fees apply for todays visit to cover diagnostic and installation. The required idler pulley was replaced. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue and was completed under parts-only warranty coverage.This repair remains covered under the original 1-year parts warranty from the first installation date (subject to manufacturer availability).; used 1 De3002a"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LFTR1835VF3
Near Redondo Beach, California 90277
Joel M.
Job Details:
11/17/2025
"Performed diagnostic on the unit. The customer reported that refrigerator not cooling. Upon inspection, I performed physical test on start device. The results showed that starter blown. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace start device. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue. This repair is not covered under our 90-day labor warranty or 1-year parts warranty as parts were sourced and provided by customer."
We serviced a
BOSCH DISHWASHER
Model SGE68X55UC/52
Near Marina del Rey, California 90292
Joel M.
Job Details:
11/17/2025
"Performed diagnostic on the unit. The customer reported that dishwasher displays e24 error code. Upon inspection, I performed water flow testing through drain. The results showed that air gap is clogged. The issue occurred due to negligence. In order to resolve the problem, the following repair is needed: unclog air gap of debris. The customer approved the repair during this visit, and the required service was conducted successfully. After unclogging air gap, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue."
We serviced a
MAYTAG DISHWASHER
Model MDB8949SBM3
Near Los Angeles, California 90291
Joel M.
Job Details:
11/17/2025
"Performed diagnostic on the unit. The customer reported that dishwasher no power. Upon inspection, I performed voltage test on control board. The results showed that no output from control. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace control board.
We serviced a
ADMIRAL DRYER
Model AGD4475TQ1
Near Los Angeles, California 90293
Joel M.
Job Details:
11/17/2025
"Performed diagnostic on the unit. The customer reported that dryer not starting. Upon inspection, I performed physical assessment of door switch. The results showed that door switch broken. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace door switch. .; ordrng 1 WPW10237959 (DOOR SWITCH)"
We serviced a
AMANA REFRIGERATOR
Model ABB1921BRM00
Near Santa Monica, California 90403
Joel M.
Job Details:
11/14/2025
"Performed diagnostic on the unit. The customer reported that refrigerator not cooling. Upon inspection, I performed voltage test to heater circuit. The results showed that no voltage output. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace control board.
We serviced a
WHIRLPOOL REFRIGERATOR
Model ET1FHTXMB04
Near Los Angeles, California 90045
Joel M.
Job Details:
11/14/2025
"Returned to complete the repair on the unit after the initialdiagnosis. The required evaporator fan blade was installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of refrigerator making buzzing noise.; pckd up 1 2163777 (Fan blade)"
We serviced a
LG DRYER
Model DLG2351W
Near El Segundo, California 90245
Joel M.
Job Details:
11/14/2025
"Performed diagnostic on the unit. The customer reported that dryer not heating. Upon inspection, I performed continuity testing on high limit. The results showed that high limit open. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace high limit thermostat and conduct annual cleaning. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 6931EL3003C (THERMOSTAT - REGULATING OR HI LIMIT) from stock"
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDT545PSJ2SS
Near Los Angeles, California 90291
Joel M.
Job Details:
11/14/2025
"Performed diagnostic on the unit. The customer reported that dishwasher not starting. Upon inspection, I performed function test on user interface. The results showed that unresponsive/dead. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace user interface and wiring.; ordrng 1 WD21X10545 (AC HARNESS ASM) and 1 WD21X31910 (USER INTERFACE)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF750SAYM1
Near Los Angeles, California 90066
Joel M.
Job Details:
11/14/2025
"Performed diagnostic on the unit. The customer reported that dishwasher leaking. Upon inspection, I performed physical inspection and ran test cycle. All components tested within manufacturer specifications, and no mechanical, electrical, or operational issues were detected during the visit. At this time, the unit is operating as designed and does not require any repairs. The customer was advised to continue monitoring the appliance and to contact us if the issue reoccurs or worsens. This service call is warranted for 14 days from the date of the visit, in case the same issue reappears."
We serviced a
WHIRLPOOL DRYER
Model LGR5636JQ0
Near Los Angeles, California 90034
Joel M.
Job Details:
11/13/2025
"Performed diagnostic on the unit. The customer reported that dryer making noise. Upon inspection, I performed run test on moving components. The results showed that idler pulley and rollers squeaking. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: install repair kit of pulley, rollers and belt. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 4392065 (BELT (DRUM), IDLER PULLEY AND ROLLERS (2)) from stock"
We serviced a
GENERAL ELECTRIC OVEN
Model JT5500SF3SS
Near Los Angeles, California 90025
Joel M.
Job Details:
11/13/2025
"Returned to complete the repair on the unit after the initialdiagnosis. The required relay board and sensor were installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of cooling fan not turn on."
We serviced a
MAYTAG DISHWASHER
Model MDBTT60AWB
Near Los Angeles, California 90045
Joel M.
Job Details:
11/13/2025
"Performed diagnostic on the unit. The customer reported that dishwasher light blink and not start. I performed physical inspection of unit. The results showed that tattered insulation, rodent feces and semi chewed lines. The issue occurred due to rodents. Recommend replacing unit after rodent issue resolved by professional pest control.
We serviced a
ELECTROLUX DRYER
Model NOTAVAILABLE
Near Los Angeles, California 90047
Joel M.
Job Details:
11/13/2025
"Performed diagnostic on the unit. The customer reported that dryer displays e66 error. Upon inspection, I performed continuity testing on limiter. The results showed that limiter open. The issue occurred due to overheating. In order to resolve the problem, the following repair is needed: replace limiter and have vent cleaning company clean and install duct under crawl space. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue.; used 1 137032600 (THERMOSTAT - 2 WIRE) from stock"
We serviced a
VIKING MICROWAVE
Model DM0C205SS
Near Los Angeles, California 90024
Joel M.
Job Details:
11/13/2025
"Performed diagnostic on the unit. The customer reported that . Upon inspection, I performed function tests and ran test cycle. All components tested within manufacturer specifications, and no mechanical, electrical, or operational issues were detected during the visit. At this time, the unit is operating as designed and does not require any repairs. The customer was advised to continue monitoring the appliance and to contact us if the issue reoccurs or worsens. This service call is warranted for 14 days from the date of the visit, in case the same issue reappears.
We serviced a
MAGIC CHEF DRYER
Model MCSCWD27W5
Near Los Angeles, California 90066
Joel M.
Job Details:
11/12/2025
"Performed diagnostic on the unit. The customer reported that not fully drying. Upon inspection, I performed function testing on all components. The results showed that all components working but drain hose too high to fully drain water. The issue occurred due to bad installation. In order to resolve the problem, the following repair is needed: lower drain hose clearance by plumber or contractor
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Redondo Beach, California 90278
Joel M.
Job Details:
11/12/2025
"Performed diagnostic on the unit. The customer reported that washer not starting. Upon inspection, I performed function testing and ran test cycle. All components tested within manufacturer specifications, and no mechanical, electrical, or operational issues were detected during the visit. At this time, the unit is operating as designed and does not require any repairs. The customer was educated on proper use and advised to continue monitoring the appliance and to contact us if the issue reoccurs or worsens.
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031US
Near Los Angeles, California 90043
Joel M.
Job Details:
11/12/2025
"Performed diagnostic on the unit. The customer reported that dishwasher drain pump keep running. Upon inspection, I performed run test on unit to find leaks. The results showed that sump and drain pump leaking in pan and vent seal leaking down door. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace sump assembly and vent seal
We serviced a
MAYTAG DRYER
Model MGDC200XW2
Near Los Angeles, California 90045
Joel M.
Job Details:
11/12/2025
"Performed diagnostic on the unit. The customer reported that the dryer not heating enough. Upon inspection, I performed resistance testing one heater components. The results showed that parts out of spec. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace coils, igniter and flame sensor.
We serviced a
GENERAL ELECTRIC DRYER
Model GTD33GASK0WW
Near Santa Monica, California 90404
Joel M.
Job Details:
11/12/2025
"Returned to complete the repair on the unit after the initial diagnosis. The required front drum bearing was installed successfully.After installation, I performed functional testing to confirm the repair.The unit is now operating as designed. This repair resolves the previously identified issue of making noise and not drying."
We serviced a
MAGIC CHEF RANGE
Model 31213WAV
Near Santa Monica, California 90403
Joel M.
Job Details:
11/12/2025
"Performed diagnostic on the unit. The customer reported that front right burner explodes. Upon inspection, I performed function testing on burner. The results showed that burner decaying making big hole for gas. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace front right burner assembly. .; ordrng 1 WP3412D025-09 (BURNER - SEALED TOP ACCESSED)"
We serviced a
MAYTAG WASHER
Model MVWB850WQ2
Near Los Angeles, California 90292
Joel M.
Job Details:
11/12/2025
"Performed diagnostic on the unit. The customer reported that washer making noise. Upon inspection, I performed function test on unit. The results showed that unit body rusted and going into wash basket. The issue occurred due to wear and tear. In order to resolve the problem, the following repair is needed: replace body. The total cost for the repair exceeds costs of repair.
We serviced a
LG DRYER
Model DLGX7801WE
Near Marina del Rey, California 90292
Joel M.
Job Details:
11/11/2025
"Performed diagnostic on the unit as a callback visit. The customer reported that dryer making noise. Upon inspection, I performed function testing on rollers and confirmed that the issue is the same as the one previously repaired on 8/5/25 but on back rollers. Since the same problem reoccurred after 90 days but within 1 year of the original repair, the part(s) are covered under warranty, but labor and service call fees apply for todays visit to cover diagnostic and installation. The required back drum rollers were replaced. After installation, I performed functional testing to confirm the repair. The unit is now operating as designed. This repair resolves the previously identified issue and was completed under parts-only warranty coverage.This repair remains covered under the original 1-year parts warranty from the first installation date (subject to manufacturer availability).; used 2 4581EL2002L (DRUM ROLLERS (2)) from stock"
We serviced a
ELECTROLUX DRYER
Model EFMG627UTT0
Near Los Angeles, California 90025
Joel M.
Job Details:
11/11/2025
"Performed diagnostic on the unit. The customer reported that dryer need installation. Upon inspection, I performed visual assessment of what needed to be done. The results showed that gas line completely missing and vent hose tearing. The issue occurred due to external influences. In order to resolve the problem, the following repair was performed: replaced vent hose and installed gas line. The customer approved the repair during this visit, and the required parts were installed successfully. After installation, I performed functional testing to confirm the repair. Also performed gas leak testing confirming no gas leaking from unit.The unit is now operating as designed. This repair resolves the previously identified issue. This repair is covered under our 90-day labor warranty and 1-year parts warranty (unless otherwise noted)."
We serviced a
KENMORE DRYER
Model 796.91182310
Near Beverly Hills, California 90211
Joel M.
Job Details:
11/11/2025
"The client requested annual maintenance on the dryer. $399Prior complaints about the unit smelling burnt was reported by the customer.Fire occurred in dryer observed and resolved Performed the following tasks:-Vacuumed dryer interior (lint chute, blower housing, motor bay)-Inspected belt, idler pulley, rollers, and seals-Functional test of heating cycle and temperature rise-Performed airflow test at unit-to-wall vent connectionResult:Issues found, recommend further repair: Need to have vent in wall cleared professionally."